How To Repair A Leather Jacket?

Genuine leather jackets are expensive and replacing them is not a cost-conscious decision. Often, people stop wearing their leather jackets if they have a tear in them. When fixing a tear in a leather jacket, you can extend the wear of the jacket. Moreover, a leather jacket can be used for several years, however, a rip, tear or holes on the jacket is a common occurrence. Repairing a leather jacket is the best possible way to salvage it from damage. As they say, a stitch in time saves nine, fixing the jacket in the nick of time is sure to make it last for a while. Don’t worry, we are here to help you with the mending work.

Nature of the damage

First thing matters before repairing a Leather Jacket is to know about nature of the damage. Is it a tear, hole or broken zipper damage issue. After it, you will be able to decide to use a method of repairing you jacket. These issue depends further that either these damages causing in minor or major quantity to your leather jacket. So, before discussing the repairing process in depth, have a look on these issues and their repairing processes shortly.

Holes

Thoroughly clean the damaged part with a good quality cleaning product. Remove the liner along the seam, so that the underside is accessible.
Cut a leather patch large enough to cover the area. Stick this patch to a small piece of canvas material with the help of fabric glue. Once the applied glue is dry, fit the canvas backed patch into the hole from the back side using leather glue.

Tear

If the size of the tear is small, hold the torn part tightly with your fingers and apply the glue with the help of a toothpick. Take a small piece of cloth and attach it to the underside with a water-based glue.

Broken Zipper

Cut the stitches of the old, damaged zipper with the help of a small knife or seam ripper. Place the new zipper on the jacket where it has to be stitched and then pin it up with a few safety pins so that it does not get displaced. Open the zipper and stitch both its sides on to the jacket with needle and thread. After it is secured, remove the safety pins.
Instead of folding it, hang it on a wide padded hanger. To prevent the leather from drying out, you must condition it regularly. Keep it clean by wiping it off with damp cloth immediately.

Sewing A Leather Patch

Well. It is a way to repair a crack in leather jacket with a moderate difficulty and need about 3 hours to complete and here we are sharing it with you in seven easy steps.

Tools Required

Fabric Glue
Fabric Scissors
Piece of Genuine Leather that Matches the Tearz
Thread that matches the leather

Sewing Needle
Scotch tape

Step 1

Turn the leather to the part that is not visible when using or wearing. Make sure that the tear is in visible sight for the repair.

Step 2

Use invisible scotch tape to tape over the tear. This tape will hold the tear closed. The piece of tape should be slightly bigger than the tear. Make sure that the tape is not too sticky so that it does not damage the leather. Pressing your finger on the sticky part of the tape will help make the tape less sticky.

Step 3

Cut a piece of leather for the patch that is slightly larger than the tear. The tear in this procedure was 1″ long so the piece of leather that was cut was 1 and a 1/2″ on each side.

Step 4

Put a thin layer of fabric glue and the patch and lightly touch it on the tear. Put the fabric glue in every section of the leather square so that it is secure over the tear. Even though it is only supposed to be a light touch, the patch has to be secure.

Step 5

Turn the leather jacket back to its original side and put a little dab of it in between the hole. Also, squeeze the tear together gently to make sure that the glue is holding it closed. After this, wait for two hours for glue to completely dry.
Use a toothpick for an easier way to keep the glue only in the tear. The glue could make a mess on the leather if the toothpick is not used. Make sure you wait the complete 2 hours of drying time for the best results

Step 6

After the glue has dried, remove the tape over the tear completely and be careful. Some of the fibers in the leather may come off on the piece of tape when it is removed. This is okay, but try to make it a very minimal amount.

Step 7

Turn the leather jacket inside out again and sew the patch of leather you put over the tear to the inside of the jacket. After this is done, the repair is complete. If you have leftover glue around the tear, then this would be the time that leather cleaner would be used. Make sure you use a sturdy needle because leather is a very thick fabric. Also, make sure that the hole on top of the needle is big enough for the thread.

Conclusion of this procedure

Leather is a difficult fabric to deal with and a tear can cost you an expensive repair. This repair is a fairly easy way to fix a repair that will save you time and money as well as add years to your leather item.

Patching Large Damaged Areas in A Leather Jacket

Patching is usually the best way of fixing holes, jagged rips, and tears more than about two inches (5.1 cm). Make sure that the piece you use is big enough to fully cover the damage from at least 1⁄4 in (0.64 cm) on either side.

When the tear you are trying to patch is two inches (5.1 cm) long, for instance, you will want to use a bit of tape that is around 2 1⁄4–2 1⁄2 inches (5.7–6.4 cm) in length.
The tape will seal the tear up and keep the edges of the leather from dividing until you can put on the patch.
Dab fabric glue into the tear out of the visible side of this coat. Turn the coat right-side out again, being careful to not dislodge the tape on the bottom of the affected region.

Use only enough glue to fill in the gaps in the material. If you overdo it, you might wind up getting noticeable crusty stains on your coat after the glue dries. Make certain to pick up a kind of fabric glue that is specifically meant for use on leather.

Like the tape, a preliminary program of adhesive will help hold the edges of the tear together as closely as possible. Permit the paste to dry for at least 30 minutes.

Many leather-suitable fabric types of glue are intended to cure in a few minutes, but it is a good idea to give it a little longer because you want the bond to be nice and protected. Meanwhile, hold off on touching your coat so as not to undermine the paste’s grip. Locate a cool, dry place to leave your coat where it will not be disturbed or exposed to environmental moisture.

If you are working with a heat-set sort of glue, wave a hairdryer or heat gun over the glued tear for 20-30 minutes to accelerate the process along. Cut a patch large enough to cover the damage from a fitting piece of leather.

As you’re waiting for the adhesive to complete setting up, catch a utility knife or sharp pair of scissors and carefully cut out your own patch. To fortify a 1 in (2.5 cm) round hole, for example, you’d want to use a patch that is roughly two inches (5.1 cm) square or round.

You’ll find leather samples in various colors, textures, and finishes in any craft shop or sewing supply store. One of those samples will make the ideal raw material for a patch.
When the glue has had time to dry thoroughly, turn the coat inside out one more time and apply a little bit of glue on the bottom of the patch, with a zig-zag blueprint for improved coverage.

Peel off the tape holding the tear together from the inside of the coat and press the patch on the leather in its location. Keep pressure on the patch for 20-30 seconds, or until it is set enough to stay put by itself. After sticking in your patch, allow the glue dry for another half hour before continuing.

When you have made your way around the patch, snip the thread and knot the ends to keep them from slipping out. Your jacket will then be all set for a night out on the town! Start and finish your stitches on the inside of the coat so your finished knots will not be observable. For a much stronger and long-lasting repair job, consider mixing a leather patch with a leather repair compound and a coating of new leather dye.

Hiding Mended Areas of Leather Jacket with Leather Repair Compound

Spread a thin layer of leather repair compound on the fixed area. Scoop up a little bit of compound with the included applicator tool and smooth it on the seam left behind in the hole or tear you just fixed. Make certain to brush a small compound onto the surrounding region, as well–this can help create a more consistent-looking finish when it is time to combine it.

The heavier you employ it, the more noticeable it’ll be. When the leather repair chemical you purchased did not come with an applicator, a plastic knife or similar utensil will do the job just as well. Heat-set the chemical using a hairdryer or heat gun for about a minute. Switch your heating tool on its lowest heat setting and wave it back and forth over the new chemical, keeping the nozzle approximately 6 inches (15 cm) away from the leather. The vast majority of leather fillers on the market are formulated to place within 60-90 seconds with continuous exposure to heat.

The chemical will take on a dull matte finish once it is fully set. You could also allow the chemical air dry if you do not have a hairdryer or heat gun handy, though this may take up to an hour under normal conditions. Buff the chemical using a sheet of high-grit sandpaper. Proceed over the dried chemical lightly using smooth, circular motions. As you do, you will notice it growing fainter and fainter in look. The idea is to slowly blend the chemical into the leather around the tear so it’s not quite as obvious.

If your leather repair compound came within a kit, it will probably contain sandpaper for mixing. If not, start looking for a sheet that is 220-grit or higher. Be careful not to remove any of these chemicals within the fixed area itself.
It may be necessary to apply another coat of compound if the damage is still visible after mixing your first coat.
If you’re able to still find the dried compound after mixing it into the leather, 1 thing you can do is buy a bottle of leather dye for a fast and effortless cover-up. Once it is dry, you will hardly be able to tell your coat was damaged in the first place!

When the dye is operating or beading on the leather, then lightly blot it with a clean portion of your cloth or sponge to remove the surplus and work the remaining dye deeper into the organic textures of this leather. Leather dyes can be found in a wide selection of colors. Make certain to pick a color that most closely matches your coat’s authentic color

Overall Conclusion.

All these repairing methods of Leather Jackets are for genuine or real leather jackets. For synthetic Leather or faux Leather Jackets, Repairing methods for faux leather jackets are different, we will discuss them in our next blog, If you wanna buy a real or genuine leather jacket, rely on Leather Jacket Gear provides free shipping worldwide. Leave your comment below regarding this blog and also share it on social media.

Author: admingear